20kV铠装移开式开关设备 KYN28A系列

2-.jpg

型号及含义
Brief introduction to the products

未标题-6.jpg

产品简介
Brief introduction to the products

KYN28A-24铠装移开式交流金属封闭开关设备(以下简称开关设备),适用于户内三相50/60Hz、额定电压24kV的单母线及单母线分段电力系统的成套配电装置。
主要应用于电厂、中小型发电机送电、工矿企业配电以及电业系统的二次变电所,作为接受和分配电能并对电路实行控制、保护和监测。
本开关设备具有防止带负荷推拉断路器手车、防止误分合断路器、防止接地开关处在闭合位置时关合断路器、防止误入带电间隔、防止在带电时误合接地开关的“五防”联锁功能。KYN28A-24开关设备配置性能优良的VS1系列中置式高压交流真空断路器或固封式真空断路器。开关设备二次回路配置先进可靠的控制保护元件,母线采用热缩绝缘材料或环氧涂覆手段,优化电极形状,柜体结构紧凑,方案组合灵活方便。

The KYN28A-24kV Sheathed Move-Off Style AC Metal-Enclosed Switchgear (hereinafter referred to as Switchgear) is a complete set of power distribution devices for single bus and single sub-bus power system, indoor three-phase 50/60Hz, rated voltage 24kV, which is mainly used for small and medium-sized generators as well as the secondary substation of the mining enterprises for the control protection and testing of the electric circuits. The switchgear has the interlock functions of the “five prevention”, ie to prevent the pushing and pulling of circuit breaker hand cart, to prevent the circuit breaker from error operation, to prevent the operating grounding switch from disconnection, to prevent the operator from error entering the live cabin, to prevent the grounding switch from error connection when it is in live condition. The KYN28A-24kV switching equipment is configged with excellent VS1series infix high-voltage AC vacuum circuit breaker or solid closed-type circuit breaker. The secondary circuit of the switchgear is configged with reliable protection components. The heat-shrinkable insulating material or epoxy coating is adopted for the bus. The electrode shape is optimized. The cabinets are compact.The combination of layout plans is flexible and convenient.

产品引用标准
Standards for Product

GB1984         高压交流断路器

GB-3906        3~35kV交流金属封闭开关设备和控制设备

GB/T11022      高压开关设备和控制设备标准的共用技术要求

DL/T404        户内交流高压开关设备订货技术条件

DL/T593        高压开关设备的共用订货技术导则

IEC62271-200    额定电压1kV以上和52kV及以下交流金属封闭开关设备和控制设备


GB1984                  High-voltage AC circuit breaker

GB-3906                 3 ~ 35kV AC closed metal switchgear and control equipment

GB/T11022             The technical requirements of the high-voltage switchgear and control equipment standard

DL/T404                 The technical requirements for ordering the indoor AC high-voltage switchgear

DL/T593                 The technical guide for ordering high-voltage switchgear

IEC62271-200         AC closed metal switchgear and control equipment, rated voltage ≥ 1kV or ≤ 52kV


技术参数
Product Structure

未标题-7.jpg


使用条件
Conditions of Use

※ 环境温度:最高温度+40℃,最低温度-15℃,24h内测得平均值不超过35℃

※ 相对湿度:日相对湿度平均值不大于95%,月相对湿度平均值不大于90%,

※ 水蒸气压力:日水蒸气压力平均值不大于2.2kPa,月水蒸气压力平均值不大于1.8kPa,

※ 海拔高度:1000M及以下

※ 地震烈度:不超过8度

※ 无火灾、爆炸危险、严重污秽、化学腐蚀及剧烈振动的场所。

※ 特殊使用条件:

    在超过GB/T11022规定的正常环境条件下使用时,本公司和用户可就超出运行条件的特殊运行条件进行协商,并达成协议。

    为防止凝露现象,开关可选用固封式,开关设备也设有加热器,当开关设备正常运行时也应注意投运加热器。


Ambient Temperature: Maximum temperature +40℃, Minimum temperature -15℃, average temperature measured within 24 hours ≤ 35℃

Relative Humidity: Average daily relative humidity ≤ 95%, average monthly relative humidity ≤ 90%,

Water Vapor Pressure: Average daily water vapor pressure ≤ 2.2kPa, average monthly water vapor pressure ≤ 1.8kPa,

Height above sea level: ≤ 1000M

Seismic Intensity: ≤ VIII

The site without fire hazard, explosion, severe contamination, chemical corrosion and violent vibration.

Special Conditions of Use:

When the product is used under the conditions not in accordance with GB/T11022,  negotiations on the special operating conditions could be carried out between the company and the users to reach an agreement. For preventing the gel phenomenon, the solid closed type switch with a heater could be used. When the switch operates under the normal condition, attention should be also paid to the operating heater.


订货须知
ordering Information

订货方在订货时应给本公司提供与产品有关的下列数据

A.完整的工程系统一次主接线图。

B.各个高压柜方案的二次原理接线图。

C.柜体的平面布置图(如有母线桥时提供其安装尺寸及布置方式)。

D.柜顶小母线布置图。

E.开关柜的备品备件数量和规格型号。

F.开关柜在特殊使用环境条件时,应在订货时以书面的形式提出。

G.开关柜壳体或面板的漆色。


The customer should provide us with the following data concerning the products:

A. The complete primary wiring diagram of the engineering system.

B. The secondary wiring diagrams of the high-voltage cabinets. 

C. The layout of the cabinets (If there is bus bridge, the installation sizes and layout should be provided).

D. The layout of the small bus at the top of the cabinet.

E. The quantity and specifications of the spare parts of the switchgears

F. While ordering the switchgears, the special operating conditions should be provided in written forms.

G. The paint color of the switchgear shell and panel.